| Features | • Mid Range Temperature |
|---|---|
| Applications | • Rail Maintenance Track Geometry |
QFA-150 Quartz Flexure Accelerometer Series
Highlights:
Compare
The Jewell Instruments QFA-150 Series Accelerometers are state of the art quartz flexure technology that provides high accuracy, repeatability and stability even in the harshest of environments.
Additional information
Performance Specifications
Performance Specifications
Performance
| Acceleration Range (g maximum)1, 2 | ±30 |
| Scale Factor (mA/g)2 | 1.1 to 1.4 |
| Bias (mg, maximum @25 °C) | 20 |
| Axis Alignment (mRad, maximum @25 °C) | ±1.5 |
| Threshold & Resolution (µg, maximum) | 10 |
| Bandwidth (Hz, minimum) | 300 |
| Scale Factor Temperature Sensitivity (PPM/°C, maximum) | |
| +25°C to +125°C | ±150 |
| +125°C to +150°C | ±200 |
| Bias Temperature Sensitivity (µg/°C, maximum) | ±100 |
| Scale Factor Stability (1 month composite) | <250 PPM |
| Bias Stability (1 month composite) | <250µg |
| Noise (mgrms, maximum) (0Hz to 10kHz, maximum) | 3 |
Electrical
| Input Voltage (Vdc) | ±12 to ±18 |
| Input Current (mA) | ±13mA max @ ±18Vdc input |
| ±10mA nominal @ ±15Vdc input | |
| ±8mA nominal @ ±12Vdc input | |
| Output Impedance (Ω) | External Load Resistor Dependent |
Environmental
| Operational Temperature Range | -55 to +150°C |
| Vibration (sine, maximum) | 25 Hz to 500 Hz,25g |
| Vibration (random) (Rectification, maximum) | 50 Hz to 500 Hz, 100 ug/g2rms |
| Shock (g) | 1000, 0.5msec, ½ sine |
Notes:
1: Specifications apply and are characterized up to ±1g range. The accelerometer is capable of supplying acceleration information up to ±30g but at a reduced accuracy
2: Scale factor shown in mA/g as a standard. If you require scale factor in volts/g, please specify voltage range when ordering.
3: Voltage output via customer supplied load resistor
*Specifications subject to change without notice on account of continued product development.
Related Products
DXA-100/200 Series Linear Accelerometer
Highlights:
The Jewell DXA-100/200 Series single or dual digital accelerometer takes Jewell’s highly accurate analog closed-loop sensor technology to the next level.
 |
 |
LSB Series Linear Accelerometer
Highlights:
The Jewell LSB Series Accelerometer is a general-purpose ±0.5G to ±20G linear device designed for rail, commercial, and aerospace sensing requirements. Available with either pin or a circular connector termination.
 |
 |
SMA Series Linear Accelerometer
Highlights:
The Jewell SMA Series accelerometer is a low cost, high precision sensor designed with very high accuracy. Applications include robotics, construction equipment, industrial measurement and control, and precision machining. All Emerald Series accelerometers are RoHS compliant.
ECV-IMU Inertial Measurement Unit
Highlights:
Jewell Instruments’ offers ECV-IMU Series initial measurement units which assure high accuracy in a small package. This inertial measurement unit is a cost efficient, low power consuming device which provides stable azimuth, pitch, and roll measurements in dynamic conditions. This sensor consists of 3-axis angular rate gyros, 3-axis accelerometer, 3-axis magnetometer, and optional 2-axis electrolytic tilt sensor. These IMUs have a wide operating range and are factory calibrated. Hence, they offer an accurate and fast output through RS-485.
JMA-100/200/300 Analog MEMS Accelerometer Series
Highlights:
The JMA-100/200/300 series is available in single (JMA-100), dual (JMA-200), and triple (JMA-300) axis configurations. This presents a robust and rugged design for industrial use, but with the benefit of low-cost MEMS technology.