| Dimensions | 5.43 × 2.38 × 1.22 in |
|---|---|
| Features | • Exceptional Dynamic Performance |
| Applications | • Robotics |
ECG eCompass Series
If your compass application involves vibration, acceleration, uneven terrain, or rough seas, the ECG Series, a gyro-stabilized electronic compass, is an uncompromising solution that will outperform rival units that cost more. The ECG provides remarkably accurate heading, pitch, and roll in dynamic conditions. It all starts with a precision 3-axis solid-state magnetometer. Two angular rate gyros independently stabilize pitch and roll. They augment a dual-axis, electrolytic tilt sensor that provides precise tilt measurements in static environments. Two sets of independent filters, one set for pitch and one for roll, combine gyro and electrolytic sensor measurements to provide the best available tilt measurements.
Related Products
Model 802 Deep Water Submersible Tiltmeter Series
The Model 802 DeepWater Series is the fully submersible cousin of our Model 801 Tuff Tilt Series. Performance features are the same, but the DeepWater housing is machined from a solid piece of 316 stainless steel and incorporates a high-pressure neoprene connector. The pressure rating is 250 bars (2500 meters depth). Higher-pressure versions may be special ordered. Temperature rating is governed by the neoprene connector. Wider temperature range is available with other connector types. Units are available in a variety of configurations including single axis (uniaxial), or dual-axis (biaxial), analog, digital, or 4-20mA outputs.
Modutec 1000 Series Digital Panel Meters
The Modutec 1000 takes the guesswork out of reading a small, low-cost, digital panel meter. These meters have an over-range indication of the rated value and auto-zero when there is no input signal. They also feature auto polarity which visually clues the user to a negative reading.
The Modutec 1000 features a 0.3-inch digit display in red or green for hard-to-read applications. Choose from bezel or window mount snap-on bezel – neither of which need extra hardware or panel holes. At 1.34″ x 0.75″ and panel depth less than 0.8″ these meters are easy to read, small units that fit into almost any application.
LCF-3000 Tri-Axis Analog Inclinometer
The Jewell LCF 3000 Series tri-axis inclinometer is a rugged, high accuracy version of the LCF Series. It is available with a wide range of options including single ended input power, internal temperature sensor and 4-20mA.
Model 701 Platform Tiltmeter Series
The Model 701-2 Platform mount tiltmeter is our most popular design for high precision tilt measurements. Units come with built-in invar leveling legs, for easy installation on any horizontal surface. The A701-2 also includes two switchable gains and two low-pass filter settings. Using an absolute gravity-referenced electrolytic sensor, the A701 delivers ultra-high sensitivity to <0.1 µrad with virtually zero long-term drift. The output is a stable ±8 DC voltage (±16 VDC differential). The D701 digital version has onboard memory, with a storage capacity of up to 22,000 samples.
Model 820 Shallow Water Tiltmeter Series
The model 820 Shallow Water is a high-precision submersible tiltmeter for use in fresh and saltwater applications. Using an absolute gravity-referenced electrolytic sensor, the 820 delivers superior measurement accuracy with virtually no long-term drift. High-gain units are sensitive to <0.0017 mm/m or better. Output options include analog (±5 VDC, ±10 VDC), current (4-20mA), and digital (RS-232 and RS-422). All units are rated to 200 meters (656.2 ft) waterproof for advanced protection from the elements. Use the 820 “Shallow Water” for structural monitoring, angle measurement and control, platform leveling, and more.
Model MD900-T Digital Clinometer
The biaxial model MD900-T is an economical digital clinometer with powerful firmware features. User programmable settings include AUTO-zero (tare), baud and output rate, sample averaging, and more. Output is RS-232 or RS-422 (RS-485 full-duplex). The MD900-T easily integrates with a variety of GPS receivers and supports Trimble TCM, NMEA XDR, BAE, and Ashtech output protocols. Units ship standard with 6-ft. hook-up cable and a 100-240VAC power transformer. Use the MD900T for industrial pitch and roll measurement, marine piling, dredging and construction systems, platform leveling, geotechnical monitoring, and more.
Modutec BL Series
The MODUTEC BL Digital panel meter gives you all the functionality you need with none of the extras you don’t need. That means simplicity, easy readability, a small footprint, and a low cost.
Jewell DPM 48×96
The digital panel meter, DPM 48×96 has been designed for industrial automation and laboratory uses which frequently require precise, onsite adjustment of the display range. With versions available for current (A, B), voltage (C, F) sensors, this panel meter is a cost-effective choice for virtually all switchboard instruments.
*Note: Models AC & T no longer available.
IRIS-SC Digital Signal Conditioning Card
The IRIS-SC digital signal conditioning card is a powerful control device designed for use with all Jewell miniature tilt sensors. Output is ASCII RS-232 or RS-422(485) serial. Standard firmware includes five user-programmable alarm/trigger thresholds for tilts tilt switch/control applications. When a selected threshold is reached, the circuitry sets the output high
on one of the pins in the H3 control connector. Other firmware features include user-programmable data output rates, sample averaging, autozero (nulling), and baud rate. The IRIS-SC can also log up to 22,000 samples to internal memory for data dump/download on user command.
All IRIS-SC units include calibration when ordered with Jewell miniature tilt sensors (specify calibrated range on order).
Modutec 2000 Series Digital Panel Meters
You need flexibility. We provide it. We customize our meters to meet your specifications.
Model 801 “Tuff Tilt” Tiltmeter Series
The Model 801 “Tuff Tilt” Tiltmeter series combines high precision and durability in an economical instrument package. Using an absolute gravity referenced electrolytic sensor, the 801 series delivers superior measurement accuracy with virtually no long-term drift. Units are available in a variety of configurations including single axis (uniaxial), or dual axis (biaxial), analog, digital, or 4-20mA outputs.
All units are rated IP65 waterproof for advanced protection from the elements.
Jewell DPM EINE
The digital panel meter has been designed for industrial applications, which frequently require precise, onsite adjustment of the display range. It can be used in industrial automation and for laboratory uses. DPM EINE measures important electrical parameters in 3 phase 4 wire, 3 phase 3 wire, and single phase network replaces the multiple analog panel meters.















