A&M 2.5 Square Ruggedized Series
A&M 2.5 Square Ruggedized Series

A&M 2.5 Square Ruggedized Series

Highlights:

Designed and manufactured in conformance with MIL-PRF-10304 (not QPL listed). Ideal for communication or test equipment where severe environmental conditions are encountered. Available size 2.5″.

Compare
Categories: , Tags: , ,
Additional information
Available Inputs

• DC and AC Rectified inputs
• DC: uA, mA, A, V
• AC: A, V
• Plus custom-designed inputs and scales
Specifications

Specifications

PointerLance, 1.062"
Scale LengthModel 233 & 235: 1.8"
Model 236: 1.6"
Terminals10/32 Brass Stud (nuts, washers, and solder lugs provided)
Downloads

Downloads

Outline Drawing

Related Products

Jewell DS Series Moving Coil Panel Meters

Jewell DS Series – Moving Coil

Highlights:

The moving coil panel meters DS 48/72/96/144 are housed in cases made of molded polycarbonate and are suitable for the measurement of DC current and voltages. These instruments offer several advantages in switchboards and Generating Set panels. A number of meters can be mounted in a Panel Cut out (Mosaic mounting). The front glass, bezel, and dial can all easily be replaced.

Compare
LSRP Single-Axis Analog Inclinometer

LSRP Single-Axis Analog Inclinometer

Highlights:

The Jewell LSRP Series inclinometer is an extremely sensitive, rugged transducer designed to provide horizontal angle or vertical deviation measurements with virtually infinite resolution. These fluid-damped compact, cylindrical-shaped sensors are stackable to meet the needs of applications with space constraints while facilitating the use of several inclinometers for multi-axis measurements.

RoHs_logo

 

 

 

 

Compare
Jewell DS Series Moving Coil Panel Meters

Jewell DE Series – Moving Iron

Highlights:

The moving iron panel meters, DE 48/72/96/144 housed in cases made of molded polycarbonate are suitable for the measurement of AC currents for the frequency range of 15 to 400 Hz and voltages in the frequency range of 15 to 100Hz. Moving iron meters indicate RMS values practically independent of waveform even of high harmonics. An error of indication may occur for extreme waveforms (e.g. phase gating controls) & for frequencies above 100KHz.

These meters offer several advantages in switchboards and generating set panels. A number of meters can be mounted in a panel cutout mosaic mounting. For CT-operated ammeters, dials can be fitted based on CT ratio. Glass and bezel can easily be replaced.

Compare
Place holder

Emico Series 802

Highlights:

Series 802 are very small, low-cost, uncalibrated devices for indicating on-off conditions or voltage transition points. They are rugged, dependable, and require less than 2mW to move the flag or pointer. The two types are:

Flag Type (802F)  – A white flag moves from one end of the red & white scale to the other when a predetermined voltage value is exceeded. Provides on-off indication.

Pointer Type (802P) – A pointer moves across the scale to indicate circuit condition. The pointer may be factory set for left, right, or exact center position to indicate zero current. The center point can be specified for a given voltage (±5%) within the range of the device.

Either type can be made to operate with a Zener diode to indicate voltage changes as low as 1 volt.

Compare
Model A603 High Precision Platform Mount Tiltmeter

Model A603 High Precision Platform-Mount Tiltmeter

Highlights:

The model A603 platform mount tiltmeter is designed to fill the gap left by the obsoleted 520M.

Units come with the same leveling worm-gear feet that were on the 520M. The A603 also includes two switchable gains and two low-pass filter settings. Using an absolute gravity referenced electrolytic sensor, the A603 delivers ultra-high sensitivity to <2.5 nrad with virtually zero long-term drift. Output is a stable ±8 DC voltage (±16 VDC differential). Rugged, reliable, and extremely accurate, the A603 is the preferred choice for volcano monitoring, high-precision geotechnical engineering, precision metrology, radar platform leveling, and high-accuracy tilt monitoring applications worldwide.

 

 

Compare
A&M 4951 Switchboard Ruggedized Series

A&M 4951 Switchboard Ruggedized Series

Highlights:

The A&M Model 4951 power factor meters are designed to meet the requirements of MIL-M-19261 and MIL-M-16034. They are supplied as either self-contained or as a “matched-set” with the external transducer. In the external transducer configuration, the transducer is matched to the meter. Both configurations are sealed watertight.

Compare
Jewell FM Series – Frequency Meter

Jewell FM Series – Frequency Meter

Highlights:

The pointer type frequency meters, FM 48/72/96/144 are housed in molded polycarbonate cases are suitable for the measurement of frequencies in the range of 45 to 450 Hz. For maximum accuracy, the essential measuring range is obtained by suppressing the unwanted frequency span. These instruments offer several advantages in switchboard and generating set panels. A number of meters can be mounted in a panel cut out (mosaic mounting). The front glass, bezel, and dial can be easily replaced.

Compare
Jewell DGL Series – AC Ammeters/Voltmeters

Jewell DGL Series – AC Ammeters/Voltmeters

Highlights:

The moving coil, rectifier panel meters DGL 48/72/96/144 are housed in polycarbonate cases and are suitable for the measurement of AC currents and voltages. Moving coil rectifier instruments measure average values and are calibrated to indicate RMS values, assuming a sinusoidal waveform for frequencies from 40 to 10000 Hz (AC current – 40 to 1000 Hz and AC Voltage – 40 to 10000 Hz). These instruments offer several advantages in switchboards and generating set panels. A number of meters can be mounted in a panel cutout (mosaic mounting). The front glass, bezel, and dial can be easily replaced.

Compare
Model 750-200 Tiltmeter Series

Model 750-200 Tiltmeter Series

Highlights:

The 750-200 tiltmeter series is a rugged, shock and vibration resistant, dual-axis tilt sensor designed for geotechnical applications. It is available in a small, convenient package and offers the options of 0-5Vdc or 4-20mA output signals.

 

 

Compare
Jewell surface mounted MS Series analog panel meter

Jewell MS Series

Highlights:

The Jewell surface mounted MS Series analog panel meter is designed with a contemporary concave cover to reduce glare and improve readability. Rugged and durable, this aesthetically pleasing rectangular shape interfaces with today’s high technology applications.

Available in sizes 1.5″ up to 3.5″.

Compare
AMI Analog MEMS Inclinometer Series

AMI Analog MEMS Inclinometer Series

Highlights:

The AMI Series is a single or dual axis, high precision MEMS inclinometer with built-in thermal compensation. Standard units come with 0-5V, 0.5-4.5V or 4-20mA output options. All AMI series inclinometers are rated IP67 for waterproofing up to 1m. Custom ranges and output types are also available on request

 

Compare
JMI-100/200 Analog MEMS Inclinometer Series

JMI-100/200 Analog MEMS Inclinometer Series

Highlights:

The JMI-100/200 series is a robust and rugged MEMS inclinometer available in single and dual-axis configurations. The low-cost MEMS technology is great for industrial use. These units are available in single-axis or dual-axis, and we also offer three output options: 0-5VDC (S series), 4-20mA (L series), and ±5VDC (D Series).

RoHs_logo

Compare

Scroll To Top
Close
Close
Shop
Close

My Cart

Shopping cart is empty!

Continue Shopping